BELIMO ACCESORIES LIST

Buy Belimo Accessories List

Belimo Electrical Accessories

SGA24, SGF24 Positioners

These positioners are intended for the remote control of modulating actuators or for use as a minimum positioner (providing a minimum limit for the output signal from a modulating controller). Positioner SGA24 is for surface mounting with a NEMA 2 housing included. Positioner SGF24 is for flush mounting.

Pulse Width Modulation Interface PTA-250

The PTA-250 converts a single pulse-width modulated input to an analog, 2 to 10 VDC, output to modulate a Belimo -SR actuator. The PTA-250 is available for replacement of existing installations. The MFT product can replace 100% of the PTA-250 applications, more effectively.

IRM-100 Input Rescaling Module

The IRM-100 input rescaling module is designed to change non-standard voltage or current signal levels into a 2 to 10 VDC output to modulate Belimo -SR type actuators. The IRM-100 is available for replacement of existing installations. The MFT product can replace 100% of the IRM-100 applications, more effectively.

Analog to Digital Switch ADS-100

To control reheat coils and/or a fan stage in a fan-powered terminal unit. The ADS-100 is controlled by a 2 to 10 VDC reheat output of a temperature controller.

Battery Back-up Module NSV24

Several Belimo damper actuators can be used either with 24 VAC or 24 VDC. In case of power failure, the NSV24 battery back-up unit switches the damper actuator from its main AC power supply over to the 24 VDC battery to drive the actuators to their safety position. For easy maintenance, the battery back-up system is placed in the control panel, not in the actuator. Several actuators may be powered by one back-up module. The batteries are separate from the NSV24.

NSV-BAT, ZGR01, ZGR02 and Resistor Kits for Multiple Actuators

The NSV-BAT battery is for use with the NSV24 battery back-up module. It is a sealed, maintenance free, lead-acid battery. Two NSV-BAT batteries are required for one NSV24.

ZG-CBNS / ZG-CBLS Junction Box for LF (-S) and AF Actuators

The ZG-CBNS accessory is used when the application requires the wiring terminations to be made at the actuator.

Transformer ZG-X40 Power Supply, Signal Simulator PS-100

The PS-100 power supply and signal simulator is designed to operate most proportional, floating, and On/Off style actuators without the presence of a controller. The PS-100 comes with a 120 to 24 VAC, plug into the wall transformer for power.

ZG-HTR NF/AF Thermostat/Heater Kit

The ZG-HTR Thermostat/Heater kit is designed to be field installed to the original AF and NF series actuators. The ZG-HTR provides a thermostatically controlled heater which allows the original AF and NF actuators to be used below their normal low ambient temperature rating. The thermostat assembly mounts to the rear of the actuator and provides for the connection of the 24 VAC supply voltage. The actuator/heater assembly should be contained in a type of housing, similar to the ZS-100 Weather Shield, to achieve best results.

Belimo Mechanical Accessories

ZG-102 Multiple Actuator Mounting Bracket

The ZG-102 multiple actuator mounting bracket is designed for cases where it is necessary to mount two actuators to one shaft to provide extra torque. The dual mounting bracket is typically used with the AFB, AFX, AF and GM series actuators. This is due to the fact that each of these series is the highest torque range available.

ZG-AFB118 Crank Arm Adaptor Kit

The ZG-AFB118 Crank Arm Adaptor Kit for AFB, AFX, NFB and NFX Series Actuators is designed for applications where the actuator cannot be mounted directly to the damper shaft. It may be used for outside or inside the duct mounting.

ZG-AF108 Crank Arm Adaptor Kit for AF Series Actuators

The ZG-AF108 Crank Arm Adaptor Kit for AF Series Actuators is designed for applications where the actuator cannot be mounted directly to the damper shaft. It may be used for outside or inside the duct mounting.

ZG-106 and ZG-107 Universal Mounting Brackets

The ZG-106 and ZG-107 Universal Mounting Brackets are designed for applications where the actuator cannot be mounted directly to the damper shaft. They may be used for outside or inside the duct mounting. The ZG-106 and ZG-107 is provided with hole patterns to mount the AF series actuators in either a horizontal or vertical position to meet space requirements. The KH-AF crank arm is required to fully convert the AF for crank arm operation. The ZG-106 and ZG-107 are designed to mount the AF series actuators in the same mounting locations as common foot mounted, crank arm style actuators.

ZG-AFB Crank Arm Adaptor Kit for AFB, AFX, NFB and NFX Series Actuators

ZG-AF US Crank Arm Adaptor Kit for LF and Series Actuators

ZG-GMA Crank Arm Adaptor Kit GM series actuators

ZG-NMA Crank Arm Adaptor Kit AM and NM series actuators

All are designed for applications where the actuator cannot be mounted directly to the damper shaft.

ZG-LF112 and ZG-TF112 Crank Arm Adaptor Kits

The ZG-LF112 Crank Arm Adaptor Kit for LF and TF series actuators is designed for applications where the actuator cannot be mounted directly to the damper shaft. It may be used for outside or inside the duct mounting.

ZG-LF2 and ZG-TF2 Crank Arm Adaptor Kits

The ZG-LF2 Crank Arm Adaptor Kit for LF and TF series actuators is designed for applications where the actuator cannot be mounted directly to the damper shaft. It may be used for outside or inside the duct mounting.

ZG-LFC114 Crank Arm Adaptor Kits

The ZG-LFC114 Crank Arm Adaptor Kit for LF series actuators is designed for Trane voyager economizer actuator retrofit.

ZG-ECON1 and ECON2 Crank Arm Adaptor Kits

The ZG-ECON1 Crank Arm Adaptor Kit for LF and series actuators is designed for applications where the actuator cannot be mounted directly to the damper shaft. It may be used for outside or inside the duct mounting.

Jack Shaft Adaptors ZG-JSA-To Adapt Hollow Jack Shafts to Fit Belimo Actuators. The ZG-JSA jack shaft adaptors are designed to be inserted into hollow jack shafts which have an outside diameter greater than 3/4 inch and provide a 3/4 inch shaft for mounting Belimo actuators.

ZS-100 Weather Shield

The ZS-100 weather shield provides moderate protection to actuators which are mounted outdoors. This product is not designed as a water tight enclosure. The weather shield will work with all damper actuators.

ZS-150 Weather Shield

The ZS-150 weather shield provides moderate protection to actuators which are mounted outdoor. The one piece, smoke tinted, polycarbonate housing allows easy mounting over all damper actuators. The tinted, clear housing allows easy viewing of the actuator in operation.

ZS-260 Explosion-proof Housing

The ZS-260 explosion-proof housing may be used with the GM, AM, NFB, NFX, AFB, AFX, AF, LF series actuators. This housing is not designed for direct coupling.

ZS-300 Protective Housing

The ZS-300 (-1) NEMA 4X enclosures may be used with AMB, GMB, LF, NF, NFB, NFX, AFB, AFX and AF Belimo actuators. They are intended for use primarily to provide protection against corrosion, windblown dust and rain, splashing water, hose-directed water; undamaged by the formation of ice on the enclosure. Type 304 stainless steel enclosures resist moisture, dust, salt, and corrosive chemicals, and are easy to keep clean for sanitary applications.

Belimo Multi-Function Technology (MFT) Accessories

ZIP-RS232 US

The ZIP-RS232 for interfacing PC with MFT US type actuators is used with the Belimo PC-Tool software (MFT-P US) to interface all Multifunctional (MFT US) type actuators via an RS232 port. Monitoring and parameterization of one MFT actuator is enabled. The ZIP-RS232 can also be used to interface the MFT actuators functionality via the UK24LON.

 

As a global leader in the design and production of actuators and control valves for commercial HVAC units, Belimo Americas products are renowned for innovation and quality. Their portfolio of accessories covers a wide range of requirements and provides energy efficient solutions for any building environment.

SGA24, SGF24 Positioners:

SGA24, SGF24 Positioners are designed for actuator modulation by remote control or as minimum positioners. The SGA24 positioner is intended for surface mounting and includes a NEMA 2 housing. The SGF24 positioner was developed for flush mounts.

Pulse Width Modulation Interface PTA-250:

Developed for the conversion of single pulse-width modulated inputs into modulated analog outputs between 2 and 10 VDCs, the PTA-250 is essential for Belimo-SR actuator operations. Readily available to replace established installations, PTA-250 applications can substituted more effectively with MFT products.

IRM-100 Input Rescaling Module:

The IRM-100 input rescaling module was developed to convert uncommon voltages or signals into VDC outputs between 2 and 10. These conversions are then used to control Belimo-SR actuators. IRM-100 modules are available for preexisting installation replacement. MFT products can effectively replace IRM-100 applications 100% of the time.

Analog to Digital Switch ADS-100:

The ADS-100, modulated by a 2 to 10 VDC reheat output, controls reheat coils and fan-powered terminal unit fan stages.

Battery Back-up Module NSV24:

Many Belimo damper actuators can utilize 24 VAC or 24 VDC. With power failures, the NSV24 back-up battery unit shifts the damper actuator from AC power, its main supply, to a 24 VDC battery. This pushes the actuators into their safety positions. For painless maintenance, the back-up battery unit is placed inside the control panel, not the actuator itself. Several actuators can receive power from one back-up unit. NSV24 batteries are separate.

NSV-BAT, ZGR01, ZGR02 and Resistor Kits for Multiple Actuators:

For use in conjunction with the NSV24 back0up battery module, the NSV-BAT battery is a maintenance-free, sealed, lead-acid unit.

ZG-CBNS / ZG-CBLS Junction Box for LF (-S) and AF Actuators:

The ZG-CBNS attachment is needed when the product involves wiring terminations made at the actuator itself.

Transformer ZG-X40 Power Supply, Signal Simulator PS-100:

The majority of floating, proportional, and On/Off actuators can be operated by the PS-100 power supply and simulator signal. The PS-100 model comes with a 120 to 24 VAC power transformer.

Other Belimo Accessories include:

ZG-102 Multiple Actuator Mounting Bracket

ZG-AFB118 Crank Arm Adaptor Kit

ZG-AF108 Crank Arm Adaptor Kit for AF Series Actuators

ZG-106 and ZG-107 Universal Mounting Brackets

ZG-AFB Crank Arm Adaptor Kit for AFB, AFX, NFB and NFX Series Actuators

ZG-AF US Crank Arm Adaptor Kit for LF and Series Actuators

ZG-GMA Crank Arm Adaptor Kit GM series actuators

ZG-NMA Crank Arm Adaptor Kit AM and NM series actuators

ZG-LF112 and ZG-TF112 Crank Arm Adaptor Kits

ZG-LF2 and ZG-TF2 Crank Arm Adaptor Kits

ZG-LFC114 Crank Arm Adaptor Kits

ZG-ECON1 and ECON2 Crank Arm Adaptor Kits

Jack Shaft Adaptors ZG-JSA

ZS-100 Weather Shield

ZS-150 Weather Shield

ZS-260 Explosion-proof Housing

ZS-300 Protective Housing

Belimo Multi-Function Technology (MFT) Accessories

ZIP-RS232 US